ASME BPE (Revision of ASME BPE). Bioprocessing. Equipment. AN AMERICAN NATIONAL STANDARD. Three Park Avenue. Buy ASME BPE Bioprocessing Equipment from SAI Global. No reproduction may be made of this material without written consent of ASME. ASME BPE (Revision of ASME BPE) Bioprocessing.

If piping support is required within a classified space, a hygienic support system shall be used.

ASME BPE Bioprocessing Equipment_图文_百度文库

Any reduction in line size should be made behind the primary nozzle connection behind panel structurethus allowing all connections asmf be the same size on the front of the panel.

A sanitary weld must be completely penetrated on the weld ID, with little or no discoloration due to oxidation, and be otherwise without defects that would interfere with maintenance in a clean and sterile condition. Examples of sealed fasteners are shown in Fig. This design assures that the drain valve is always at the true low point of the assembled jumper connection in any specified orientation.

Items constructed in accordance with all of the applicable rules of ASME are identified with the official Symbol Stamp aeme in the governing code or standard. Some examples as,e polymers are plastics, proteins, DNA, and dendrimers. Bbpe, Paul Mueller Co. The purpose was to develop an ASME standard 20007 would be distinctive, germane, and not in conflict with other industry standards.

Drain marks permanently marked on both sides of the valve body will show the correct mounting position to optimize drainability. Rau, Dockweiler AG P. Also, in welding of tubing, when the weld fully penetrates the wall thickness but misses the joint, leaving some portion of the inner inside diameter weld joint with unfused edges. They can be synthesized either through chain reactions or by templating.

Recommended c Typical Hygienic Clamp Union — 1. A 207 crack will produce a liquid penetrant indication during liquid penetration inspection, X-ray, or ultrasound. Attention shall be paid to the weld between the sensor stem and the jumper. Materials of construction shall be corrosion resistant and compatible with chemical and physical performance and designed for steam service.

Straight Tee and 2070. Functional components of the CIP such as awme, pumps, vessels, tubing, and piping shall be designed to be self-cleaning and abide by the guidelines of this Part. Surface finish specification shall match the clean steam condensate tube finish specification unless the condensate downstream of the trap is used in the process or sampled for quality assurance.

All internal angles of deg or less on product contact surfaces shall have the maximum radius possible for ease of cleanability.

Arnold, Pall Filtration Pte. The downslope portion of a welded joint is seen as a tapering of the end of the weld bead with a reduction of penetration from the beginning to the end of the downslope so that the final weld bead is small with minimal penetration. Flexible Hygienic Hose Design. The test shall be performed by spraying a dye e. This standard is intended asmw design, materials, construction, inspection, and testing of vessels, piping, and related accessories such as pumps, valves, and fittings for use in the biopharmaceutical industry.

This Part shall be used in conjunction with other Parts of this Standard along with applicable references. O-ring grooves should be shaped in accordance with the O-ring manufacturer recommendation for functionality.

ASME BPE Guidelines for Pharmaceutical Equipment

Based on these objectives, the following policy has been established on the usage in advertising of facsimiles of the symbols, certificates, and references to codes or standards construction. If side-shell manways are required, they should be sloped for drainage.

Schnell, Dupont Performance Elastomers E. Return system engineering shall give consideration to balancing solution flow i.

The size of surface deficits is classified in two groups: Mount Nominal Size mm The CIP recirculation tank shall be selfcleaning via a spray device and the requisite valving and piping to accomplish this action as a part of each asem. Stover, NewAge Industries, Inc. SD, illustrations a and c ]. Pbe, Advance Fittings Corp. Three-piece-body ball valves should be used instead of single-body designs for both cleanability and maintainability. Hygienic Design Flow SD Food and Drug Administration U.

This can be accomplished by filtration, precipitation, or centrifugation. The test may be performed with ambient temperature water and before the riboflavin dye has dried.

This is usually achieved at a velocity of 5 fps 1. Concavity is measured as a maximum distance from the outside or inside diameter surface of a welded joint along a line perpendicular to a line joining the weld toes.

ASME BPE - Wikipedia

In temporary runs, hose assemblies may be manually drained after disconnecting. Klemp, Advance Fittings Corp. SD, illustrations a and d ].

Acceptance Criteria for Welds on Tube. A weld joint is said to be fully aeme when the depth of the weld extends from its face into the weld joint so that the joint is fully fused. The integrated system makes it possible to achieve complete and uniform control of time, temperature, and chemical concentration, all of which are important to success with any mechanical spray or pressure recirculation CIP process.

The fused glass shall be circular in shape within the metal frame. Dvorscek, Abbott Laboratories M. The use of preservative fluids is not recommended.