There are precautions provided in ASTM A/AM that should be considered to prevent embrittlement, as well as selecting steels with appropriate. Practice ASTM A provides guidance on safeguarding against warpage and be stress relieved per the guidelines provided within ASTM A, Section 6. ASTM A / AM Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure.

Active view current version of standard.

The Eng-Tips staff will check this out and take appropriate action. Click Here to join Eng-Tips and talk with other members! Other materials that can be galvanized include continuous cast slabs, steel or iron castings, and wrought iron.

Standard Specification for Zinc Hot-Dip Galvanized Coatings on Iron and Steel Products covers individual steel pieces as well as assemblies of various classes of material. It may also be known by its trade name, e. However, if the galvanizer has to perform additional work in order to prepare the product for hot-dip galvanizing, such as drilling holes to facilitate drainage or venting, the galvanizer will communicate and resolve the issue with the customer.

Finally, there are requirements for passivating the material chromating to prevent reaction between concrete and the zinc coating, and on bend diameters.

Join your peers on the Internet’s largest technical engineering professional community. However, the AGA does provide a compilation of specifications pertinent to galvanizing. When two steels of different thicknesses are assembled and brought up to galvanizing temperature, the thinner steel heats up and expands more quickly than the thicker steel.

All fabricated assemblies shall be designed with vent and drain holes such that no air is trapped during immersion of the assemblies into cleaning solutions or molten zinc. A requires a continuous, smooth, and uniform finish with no uncoated areas including on the threads or issues that interfere with its intended use.

Inch-pounds and SI units are not necessarily exact equivalents. Standard Specification for Zinc Coating Hot-Dip on Iron and Hardware applies to hardware products such as castings, fasteners, rolled, pressed, and forged products, and miscellaneous threaded objects that will be centrifuged, spun, or otherwise handled to remove the excess zinc.

Resources Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors. Any combination of these products can be assembled into a single fabrication and then hot-dip galvanized. The requirements for finish, appearance, and adherence are identical to those in the other main standards.

ASTM A Recommendations | American Galvanizer’s Association

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Whenever different analyses of steel or aa surfaces of steel are united in an assembly the galvanized finish is not generally uniform in appearance.

The material shall undergo cold working and thermal treatment. The design of the product and selection of proper steel for its suitability to withstand normal galvanizing operations is the responsibility of the designer and fabricator.

After galvanizing, these products should be air cooled instead of quenched to minimize induced stress from the cooling cycle. KnowledgeBase What is EN ? Therefore, steel thicknesses should vary as little as possible throughout the assembly.

This practice is applicable to chromate coatings of the colorless both one and two-dipiridescent yellow or bronze, olive drab, black, colorless anodic, yellow or black anodic types, and of the dyed variety, when applied to surfaces of electrodeposited zinc, mechanically deposited zinc, hot-dipped zinc, rolled zinc, electrodeposited cadmium, or mechanically deposited coatings.

Leave this field blank. Symmetrical sections such as I-beams and tubing will be less likely to distort than asymmetrical pieces camber beams, channels, tees, custom beams, girders because the thermal expansion forces above and below the natural axes balance each other.

ASTM Specifications

The design and fabrication of the product to be galvanized are the responsibilities of the designer and the fabricator. Minimize Thick and Thin Material in the Same Assembly When two steels of different thicknesses are assembled and brought up to galvanizing temperature, the thinner steel heats up and expands more quickly than the thicker steel.

Within the text of this practice and where appropriate, SI units are shown in brackets. A also describes how to test for embrittlementessentially by comparing the bending properties of ungalvanized steel to galvanized.

The following is a summary of the various pertinent hot-dip galvanizing specifications. The specification requirements for coating thickness only contain minimums, there is no maximum coating thickness limitation in the specification. A134 reading through stacks of specs for a project we’re bidding and in the galvanizing spec one of the many lines says that ASTM A shall govern. Inspector Listing — Non-U.

ASTM A384 Recommendations

Active view current version of standard. Where welding before galvanizing cannot be avoided, the internal stresses in the connections can be minimized by avoiding joint designs or weld lengths which are greater than statically required, and by placing welds near to and symmetrically s143 the neutral axis - aligning welds so that shrinkage and opposing forces are balanced rather than all pulling in the same direction.

This specification covers zinc metal made from ore or other material by a process of distillation or by electrolysis in five grades as follows: Are you still looking for the right answer?

It may also be known by its trade name, e.