The particle size distribution of a metal powder affects its behavior in P/M processing and other applications of these materials. The test method may be part of. ASTM B Standard Test Method for Sieve Analysis of Metal Powders. standard by ASTM International, 04/01/ View all product details. Most Recent. Buy ASTM B Standard Test Method for Sieve Analysis of Metal Powders from SAI Global.

It is the responsibility of the user of asstm standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Weigh this fraction to the nearest 0. Other types of sieve shakers are also available, but their precision and reproducibility have not been determined. Over time, the correcting results should continually be evaluated. If used continually, the sieves will, after a period of time, asstm less accurate and might no longer meet the requirements set in Speci?

Standard - Standard Test Method for Sieve Analysis of Metal Powders ASTM B -

Approved April 1, This standard has been approved for use by agencies of the U. In many applications within the process, food and life sciences industries, aatm smallest amounts of a substance must be measured and added with a high degree of accuracy — whether in piping or in chemical reactors.

Practice E was followed for the design and analysis of aatm data. NOTE 2—Use of b2114 sound proof enclosure is recommended. Customer comments No comments were found for ASTM B - 07 standard test method for sieve analysis of metal powders. A second set of sieves was chosen by each laboratory from its in-house sieve stock. One set of sieves was a standard set that was circulated to each laboratory in turn.

ASTM International

The entire apparatus shall be rigidly mounted by bolting to a solid foundation, preferably of concrete. A number in parentheses indicates the year of last reapproval. Precision and Bias4 9. Standard Series sieves in each sieve nest: Report any fraction that is less than 0.

The mainly new products of Holykell company Limited displayed at this time include IOT products,water in oil sensor monitor, orifice plate flowmeter,an Proline Promass A for lowest flow rates Aug. The number of rotations per minute shall be between and Users of this standard are expressly advised that determination of the validity of any such patent rights, and astk risk of infringement of such rights, are entirely their own responsibility.

Standard Series Particle Size? Report the actual time period of sieving, if it is different than 15 minutes. Sieving time may be adjusted for such materials, and the actual time used should be reported along with the test data. N214 range of new pipe and wedge sensors featuring compact dimensions is ideal for the use in smaller flumes. Be the first to comment! Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Originally approved in Flavoring for foodstuffs, active ingredients for pharmaceuticals or corrosion-inhibiting substances in oil production are just a few astmm. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Repeat this process for each sieve in the nest. Awtm edition approved April 1, It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine asrm applicability of regulatory limitations prior to use.

Standard Series in Table 2 and examples of the Old U. NOTE 3—For some materials, for example brittle and friable materials, the 15 minutes may be too long. For circulated sieves or by analogy matched sieves obtained by two laboratories R can be calculated from the following equations: Other types b24 sieve shakers are also available, but their precision and reproducibility have not been determined. Series zstm been deleted and the columns for the Old U.

Brush any material adhering to the bottom surface of the sieve and the lower frame with a soft brush into the next? The test method may be part qstm the purchase agreement between powder supplier and user, or it may be an internal quality control test for either. Then fasten the sieve assembly securely in the sieve shaker and operate the machine for a period of 15 minutes. Add the difference between this sum and the mass of the test portion in accordance with Section 6 to the mass of the fraction collected in the pan.

By comparing sieve tests on the same sample, run in both the master set and the working set, a factor can be established for correcting results on the working sieves.

Remove the fraction collected in the pan and weigh. The test portion should be obtained in accordance with Practices B A portion of 40 to ashm g shall be used when the apparent density of the powder is less than 1. NOTE 1—The mm diameter sieve is most commonly referenced as an 8 in.

Long-Term Flow Metering with integrated Data Transmission May 14, The mobile NivuFlow Mobile flowmeter was specially developed for wastewater applications in part filled canals as well as in part filled and full pipes. The newly developed Promass A measures such substances drop-for-drop with a precision unmatched worldwide.

The test method may be part of the purchase agreement between powder supplier and user, or it may be an internal quality control test for either. ASTM B - 07 standard test method for sieve analysis of metal powders 0.

Place the test portion on the top sieve and astk this sieve with a solid cover. Committee B09 has identi?