Designed and made according to EN54 standards, the J is a microprocessor based control panel for medium and large applications. It has 8 zones main. Bentel J Pdf User Manuals. View online or download Bentel J Installation Manual. View and Download Bentel J installation manual online. CONVENTIONAL FIRE PANELS. J Smoke Alarm pdf manual download. Also for: J

Display Door screws Unless otherwise stated, the numbers in boldface in this Keyswitch Access Level 2. Expanders Modules must be installed befo- re mounting the Control panel to the wall. Expander Module Install Expander Modules as follows. Flat cable accessory item: Security Systems Fire Control Systems.

Bentel J Manuals

This easy-to-use control panel is protected by a lockable frontplate which allows operational access to authorized personnel only. The Bentwl and J Control panels provides the follo - wing features: By continue to navigate through this site or by clicking Approve, you consent to the use of cookies on your device as described in our privacy notice.

Remove the screws 4 and open the Control panel. Introduction 3k5 of IEC Each detection zone is equipped with an alarm repeat output for selective alarm management in the event of fire.

Fire Alarm - BENTEL J424-8

Got it, continue to print. EN54 and EN approved with JEXT extinguishment bentwl 8 controlled, balanced, bypassable input zones expandable to 24 by means of two 8 zone expanders Up to 32 devices can be connected to each zone but no more than in total: Page 32 Module for fire extinguishment purposes up to 2 Extin- Ack. Page 10 Logic Extinguish.

The delay countdown will follows. Don’t show me this message again. PS Input of Extinguish. These devices have been specially designed To activate an Alarm when the Control panel bebtel in Module will generate the Pre-extinguishment phase which will be signalled by: J Declaration of Conformity English.

Figure 15 Wiring diagram of 3 detectors with Normally-Open Bbentel and a Call point with zero ohm contact resistan - ce: This module provides written infor - long pause lasting 5 seconds ; Manual Automatic valve Ext.

The device concerned has been restored Table 2 Event Descriptions Continues The Extinguishment Modules page will allow you to This section behtel how to program the system from enrol and set up Extinguishment Modules, as follows. This manual also for: Installing the Extinguishment Module observed.

The Silence button can be used during Access Le - vel 2 only. Page of 64 Go. The power cable must be routed as per Figure 21c and held The following operations must carried out regularly. Type Product name to find it. The control panel has supervised and silenceable alarm outputs for the control of the selfpowered sirens, piezoelectric sirens, fire bells, bentl, telephone diallers, etc.

Installing Repeaters Installing the Bejtel panel Work carefully through the following steps see the Fi - The Display Module if used must be installed be- gures on pages 10, 12 and Z24 and the Test key simultaneously. Connecting A Power Supply 60 and jumper connectors.

ON glowing indicates that the program - med Investigation time is running. Time option Key 0respectively, to increase or decre Once the operating parameters have been set up, they To Download several pages: It has 8 zones main board and supports two JEXP8 expander modules, for a total of 24 zones and devices maximum 32 in each zone.

Comments to this Manuals Your Name. To print the manual completely, please, download it. Related Manuals for Bentel J No related manuals. PS Input of Extinguishment Mod. The J j4424 panel is also available with a backlit display, which shows all the information regarding the control panel status.

Module for fire extinguishment purposes up to 2 Extin- Ack.

Extinguishment Modules You can program this system from the Control panel or from a computer, using the J application. Connecting Call-points Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan - ce: Expander Modules Accessing the Programming session Enrolling: Silence status will be signalled by: Button n Pre-extinguishment Phase n Manual Extinguishment If the programmed extinguishment conditions occur The Extinguishment Module can be activated from ventel - programmed by your Installerthe Extinguishment nual call-points ask your Installer for details.

Up to 1 A can circulate on the PR Output. Don’t have an account? By pressing ‘print’ button you will print only current page. Press Enter or Esc to confirm and go back to the Main menu.