BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. C NTE Equvilent NTE PNP audio amplifier transistor. NTE Silicon PNP Transistor Audio Amplifier. Switch (Compl to NTEAP). NTE Data Sheet. PNP Epitaxial Silicon Transistor. Features. • Switching and Amplifier. • High- Voltage: BC, VCEO = V. • Low-Noise: BC, BC

If you are designing a PCD or Perf board with this component then the following picture from the BC Datasheet will be useful to know its package type and dimensions. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. Current flows in through collector. Controls the biasing of transistor. TL — Programmable Reference Voltage. If you are designing a PCD or Perf board with this component then the following picture from the Datasheet will be useful to know its package type and dimensions.

Some of the configurations used in amplifier circuits are Common emitter amplifier Common collector amplifier Common base amplifier Of the above types common emitter type is the popular and mostly used configuration.

TRANSISTOR C B datasheet & applicatoin notes - Datasheet Archive

As mentioned the biasing current should maximum of 5mA. BC has a gain value of tothis value determines the amplification capacity of the transistor. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

The value of this resistor R B can be calculated using below formulae. Tranistor bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA.

tarnsistor Of the above types common emitter type is the popular and mostly used configuration. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA.

When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

Amplifier modules like Audio amplifiers, signal Amplifier etc. When this transistor is fully biased transishor it can transitsor a maximum of mA to flow across the collector and emitter. BC has a gain value of tothis value determines the amplification capacity of the transistor. When a transistor is used as a switch it c575 operated in the Saturation and Cut-Off Region as explained above. As discussed a transistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

TL — Programmable Reference Voltage. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

BC557 Datasheet, Equivalent, Cross Reference Search

Submitted by admin on 30 August When base current is removed the transistor becomes fully trajsistor, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. BC is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.

A Transistors acts as an Amplifier when operating in Active Region. Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin.

Current Drains out through emitter. BC transiistor a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

Of the above types common emitter type is the popular and mostly used configuration. The value of I B should not exceed mA.

It can amplify power, voltage and current at different configurations. The value of this resistor R B can be calculated using below formulae.

C Datasheet, PDF - Alldatasheet

Amplifier modules like Audio amplifiers, signal Amplifier etc. Complete Technical Details can be found at the BC datasheet given at the end of this page. Complete Technical Details can be found at the datasheet give at the end of this page. As discussed a tranxistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

C557, PNP Silicon, Amplifier Transistor, TO-92

Submitted by admin on 26 October BC Transistor as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Anything more than 5mA will kill the Transistor; 5c57 a resistor is always added in series with base pin.

The value of I B should not exceed mA.

A Transistors acts as an Amplifier when operating in Active Region. It can amplify power, voltage and current at different configurations.